Continued From Page 3

At 9:00 a.m. in my boxer shorts, Monday morning, I met the UPS man and signed for the Barnett package. I started to lube all the cables then decided that I should get dressed.

In order to install a new clutch cable the face of the transmission must be removed. I was surprised that this was the first item that I ran across on the King that was a pain in the ass to install. The entire exhaust system had to be loosened all the way back to the rear muffler isolator. before the clutch release housing could be removed.

With large clip ring pliers the throw-out mechanism was set free to release the clutch cable which virtually snapped into place. Then the cover was spun to allow the cable housing to unscrew. Next the new cable was fed along the same route as the stock job.

Once the clutch release cover is removed and the clip ring snapped out, you can see the outer ramp with the coupling ready for the cable.

If you look close the cable has been fed through the hole and is heading towards home.

Now with the new cable attached the outer ramp heads back into position. Watch you don't tilt the case. The ball bearings will escape.

This shot shows the entire clutch release assembly complete. Remember as you reposition the clip ring to put the sharp edge up for the most secure bond.

We discovered that we had a lot of slack and rerouted the clutch cable outside the front motormount to eliminate some. Then the tranny cover gasket was wiped clean and the cover replaced (torqued to 10-12 foot pounds), then refilled with tranny fluid to the appropriate level with the bike upright and the dipstick threads just touching. We filled it to the top dipstick mark, about 3/4 of a quart capacity.

With this assembly you spin the cover onto the cable, not visa-versa.

According to the book, the torque specs call for 10-12 foot pounds of torque to snug up the clutch release cover.

With a 9/16 box end wrench snug the cable housing down with a new o-ring attached.

We jacked-up the gas tank to afford us access to the fuel injection throttle cable routing. With the three tank mounting bolts removed the tank was lifted easily until a chunk of wood could be wedged under the front of the tank. Then I figured out which cable was what. With a small Crescent wrench, I loosened the throttle cable adjusters and took out all of the adjustment to allow lots of cable slack.

The unit with the small spring around the cable at the throttle body end was the push cable. I fed the braided cables through the runners as if they were stock cables. You will note, if you attempt this, that there is a Cruise Control connection in one of the stock cables at the neck. We unplugged it with trepidation. I wasn't sure what havoc it would cause. I hadn't tried the Cruise control. As it turned out, it's a sensor to kill the control, if you back off the throttle abruptly.

Lubing throttle cables starts with wrapping the cable housing with a little masking tape to create an oil container. Fill it with a light 3-in-1, silicone, or Marvel Mystery oil and let it seep into the housing. Fill it several times.

Feed the cables up through the throttle casing. With a little force they will snap into place.

Make sure to grease the brass barrel before installing it to the cable end. The grease will help hold the barrel in place.

With the Barnett cable set at the most slack position, slip the barrel and cable onto the greased throttle guide grove.

This is not a good shot of installing the cables into the guide slots in the intake module, but it's easy. Just make sure you have the right cable in the right slot. It doesn't hurt to grease them which we forgot.

Here's the cables in position. That odd short cable on the side is the cruise control job.

Make sure you oil the throttle cables before they are snapped into the throttle housing on the bars, because the spring clips that hold them into place are a bitch to remove. The cables were both put into place with brass rollers, "After you grease the throttle and cable runners with a Q-tip," Frank reminded me. Be careful not to lose those tiny brass suckers. I was told later to try to adjust the cables evenly under the throttle and make sure you have slack in both lines so you don't have continuos drag on the cable fittings.

Here's the throttle body in place waiting for the front brake mastercylinder.

According to experts, you should adjust the cables so that the adjustment screws are approximately equal in length. My adjustment had to be straightened out at a later date.

Finally we replaced the air cleaner backing plate using Phillips screwdrivers to hold the gasket in proper position. Next the breather hoses had to be pushed onto the head fittings and lined up with the air cleaner element. Lastly the cover was installed. It was time to ride.

But not so fast Kimosabe. We had to install the riser cover, the nacelle trim and the headlight assembly. We were hauling ass.

The actual breather fittings hold the air cleaner backing plate into place.

Use small Phillips screwdrivers to hold the air cleaner gasket aligned.

Push the hoses into place keeping in mind that they feed into the air cleaner element.

This little nut and screw are a bear to replace but must be handled before the nacelle strip can be installed.

This slightly out-of-focus shot shows the little stud that slips through the nacelle. Make sure the strip is locked into the riser cover slot before you tighten the nut.

Tighten the nut lightly with blue Loctite to keep it from rattling loose.

Don't forget to plug the headlight in before you install it, like I did.

Install the headlight assembly with all eight black screws. Leave the bright adjustment ones alone, unless you lowered your bike. Then it needs adjustment.

We could screw the riser down with the Phillips screws and replace the snap-on ignition ring last. I still don't like the way it fit and need to check it again.

By noon on Monday we had completed the Highbar installation and I was itching to hit the road. We had moved our appointment at the fleet center from Friday to Monday morning, then to Monday at noon. We didn't roll up to their doors until 1:30 p.m. and Alan, the master mechanic announced that he was leaving at 4:00. We were burnin' daylight once again. Would the pressure every end?

The final Frank shot with one hand hanging outside of a van window. I want to thank Frank for the use of his tools and his photographic and technical skills. Those elements and my bumbling hands make these techs as complete as they are. Believe me, it's a bastard to build a bike, write a tech and take the shots at the same time. We've done it before, but a team efforts helps a helluva lot.

Next, we'll install a performance package with Screamin' Eagle heads, cams, air cleaner and two into one exhaust that we had jet hot coated. Hang on.

--Bandit

--