This shows just a fragment of all the parts involved.

Hang on. Here comes a complete build of a custom CCI Goliath Bike Kit. We built this 100-inch Rev Tech monster in nine days. The bike was assembled to promote the Annual Beach Ride, at the Queen Mary in Long Beach, through the efforts of Custom Chrome, George Hayward and Bikernet.com. We assembled the bike in the Bikernet Headquarters for the children's charity ride. It was also featured in three issues of American Rider, but this is the extended, unedited version with charts. Before we get started, I want to add an editorial note. If you read this and want to add something, don't hesitate. We can change the text whenever we goddamn want. If we missed something, you have a special tool, a correction or want to point out what a bunch of baboons we are, don't stop, send a Your Shot. Let's hit it.

"What the hell," Nuttboy mumble, "what did you volunteer me for?" He scratched his butt, with a 9/16 open end wrench, as we loaded box after box of components into the garage. If CCI could somehow ship the components without the retail packaging, they would save a fortune. We had a truck load of plastic peanuts, plastic bags and cardboard.

The Goliath is a complete 100 inch, Rev Tech powered Softail kit. It comes with every nut and bolt. "And a few extras," Nuttboy chimed in distractedly. Also included was a Softail manual and a Softail Parts book. We also referred to the Tim Remus book, "How To Build A Kit Bike", from Wolfgang Publications.

"The Remus book was the most help, but there were big gaps in information," Nuttboy grumbled. "We often had to scan the photos in the book in a fleeting effort to figure out a procedure that wasn't described." Maybe this series of articles will help.

The entire bike was built in a garage using normal hand tools. A professional shop came in handy on only two occasions: Pressing the clutch together, tire/wheel assembly and balancing.

The frame, wheel rims, and miscellaneous parts were powder coated by Custom Powder Coating in Dallas (214) 638-6416 to match the hue used by Santini Paint (714) 891-8895, for the sheet metal.

Here's the massive rear wheel. It was powder coated red on the rim, then clear powdered. Finally George, the Wild Brush, finished the edge with a wide stripe.

"Violent Red I'd call it," wise-cracked Nuttboy, "it looks hot enough to fry your bratwurst."

We made sure the tank was pressure tested and sealed at the painter's. We organized the parts as best we could and once the powder coating was returned Nuttboy shaved off the paint and tape where the motor mounts and tranny mounts were located. Dallas handles frames for American Iron Horse, so they know what to mask, which saved time. Nuttboy started checking the surface around the neck and beating the cups into place with a brass hammer and a massive punch. They must be pressed in completely.

We tried to organize the parts. This was the electrical stack.

We cleaned the area around the cup area on the neck to make absolutely sure the cups would seat entirely. That's critical. If the cup seats more while vibrating down the road the front end will loosen and add to crucial elements that could lead to a high speed wobble.

We used a 20-year-old Bikernet punch to drive the cups home. Make sure they're aligned properly.

You can tell by the changing tapping sound that the cup is fully in place.

Note the markings to keep matched bearings and races together.

We separated the cups from the bearings but made sure to note which matched bearing fit in which cup, for the most precise fit. Nuttboy pounded the cups in place with a dab of grease to prevent jamming inside the neck.

Custom Powder Coating did a fine job of taping off the bearing and motormount areas, but each one needed the edges cleaned.

This emery bid worked wonders to clear away paint or soften the edges.

We used a bench polisher to clean the powdered edges on this inner-primary spacer.

Here's the red billet headlight ring.

Scraping the tape free of the tranny mount for a solid bond.

Some of the frame threads needed chasing which eased assembly. Then Nuttboy bolted in the offset Tranny plate.

"The swingarm spacing was a turkey," Nuttboy coughed trying to fit the axle. The swingarm axle came with several spacers, none fit perfectly, and we were forced to make spacers and set the swingarm up several times. He gave up on the swingarm and installed the shocks first then the tranny to make allowances for the studs. One had to be shaved due to the offset tranny plate.

Here's some improved-shock instructions:
Place the motorcycle securely on a stand so no pressure is on the shocks.
Install the new shocks--the hardware was supplied
You'll need a preload wrench from a dealership to adjust (94455-89).
The preload comes adjusted to the lightest setting. To increase the preload for heavier riders/loads/passengers, loosen the 11/16 locknut and back it off several turns. Use the 11/16 Harley adjustment wrench to turn the adjustment nut counterclockwise to the desired preload setting. Then tighten the 1-inch locknut. Both shocks must be adjusted to the same equal setting.

The swingarm axle came with a variety of spacers, but no guidance. The widened frame was almost two inches wider, maybe more. We would have loved a diagram.

We grappled with it for a couple of hours, then took a research break. Part of the dilemma was the thick red powder coating on the inside of the frame and swingarm parts.

"The fifth stud was removed," Nuttboy said, "there's always a stud too many in the Bikernet garage," Nuttboy commented. Another stud was shortened for clearance. He tightened the tranny plate down but not the tranny until the inner primary is aligned. Directions indicated an Allen plug to replace the 5th stud. We couldn't find it, so shifted to plan B.

The rear right stud also was ground to clear the shocks due to the offset.

On to Page 2...